 |
|
| If you can't view the Datasheet, Please click here to try to view without PDF Reader . |
|
|
|
| If you can't view the Datasheet, Please click here to try to view without PDF Reader . |
|
|
| Datasheet File OCR Text: |
| MC74VHC1G14 Single Schmitt-Trigger Inverter The MC74VHC1G14 is a single gate CMOS Schmitt-trigger inverter fabricated with silicon gate CMOS technology. The internal circuit is composed of three stages, including a buffer output which provides high noise immunity and stable output. The MC74VHC1G14 input structure provides protection when voltages up to 7 V are applied, regardless of the supply voltage. This allows the MC74VHC1G14 to be used to interface 5 V circuits to 3 V circuits. The MC74VHC1G14 can be used to enhance noise immunity or to square up slowly changing waveforms. Features http://onsemi.com MARKING DIAGRAMS VA M G G M * * * * * * * High Speed: tPD = 4 ns (Typ) at VCC = 5 V Low Power Dissipation: ICC = 1.0 mA (Max) at TA = 25C Power Down Protection Provided on Inputs Balanced Propagation Delays Pin and Function Compatible with Other Standard Logic Families Chip Complexity: FETs = 101 Pb-Free Packages are Available SC70-5/SC-88A/SOT-353 DF SUFFIX CASE 419A Pin 1 5 5 1 SOT23-5/TSOP-5/SC59-5 DT SUFFIX CASE 483 1 Pin 1 VA M G G VA M G NC 1 5 VCC = Device Code = Date Code* = Pb-Free Package (Note: Microdot may be in either location) *Date Code orientation and/or position may vary depending upon manufacturing location. IN A 2 PIN ASSIGNMENT GND 3 4 OUT Y 1 2 3 NC IN A GND OUT Y VCC Figure 1. Pinout (Top View) 4 5 IN A 1 OUT Y L H FUNCTION TABLE A Input Y Output H L Figure 2. Logic Symbol ORDERING INFORMATION See detailed ordering and shipping information in the package dimensions section on page 4 of this data sheet. (c) Semiconductor Components Industries, LLC, 2007 1 January, 2007 - Rev. 17 Publication Order Number: MC74VHC1G14/D MC74VHC1G14 MAXIMUM RATINGS Symbol VCC VIN VOUT IIK IOK IOUT ICC TSTG TL TJ qJA PD MSL FR VESD DC Supply Voltage DC Input Voltage DC Output Voltage DC Input Diode Current DC Output Diode Current DC Output Sink Current DC Supply Current per Supply Pin Storage Temperature Range Lead Temperature, 1 mm from Case for 10 Seconds Junction Temperature Under Bias Thermal Resistance Power Dissipation in Still Air at 85C Moisture Sensitivity Flammability Rating ESD Withstand Voltage Oxygen Index: 28 to 34 Human Body Model (Note 2) Machine Model (Note 3) Charged Device Model (Note 4) Above VCC and Below GND at 125C (Note 5) SC70-5/SC-88A (Note 1) TSOP-5 SC70-5/SC-88A TSOP-5 Parameter Value -0.5 to )7.0 -0.5 to +7.0 -0.5 to VCC )0.5 -20 $20 $12.5 $25 *65 to )150 260 )150 350 230 150 200 Level 1 UL 94 V-0 @ 0.125 in u2000 u200 N/A $500 V Unit V V V mA mA mA mA C C C C/W mW ILatchup Latchup Performance mA Stresses exceeding Maximum Ratings may damage the device. Maximum Ratings are stress ratings only. Functional operation above the Recommended Operating Conditions is not implied. Extended exposure to stresses above the Recommended Operating Conditions may affect device reliability. 1. Measured with minimum pad spacing on an FR4 board, using 10 mm-by-1 inch, 2-ounce copper trace with no air flow. 2. Tested to EIA/JESD22-A114-A. 3. Tested to EIA/JESD22-A115-A. 4. Tested to JESD22-C101-A. 5. Tested to EIA/JESD78. RECOMMENDED OPERATING CONDITIONS Symbol VCC VIN VOUT TA tr , tf DC Supply Voltage DC Input Voltage DC Output Voltage Operating Temperature Range Input Rise and Fall Time VCC = 3.3 V 0.3 V VCC = 5.0 V 0.5 V Parameter Min 2.0 0.0 0.0 *55 - - Max 5.5 5.5 VCC )125 No Limit No Limit Unit V V V C ns/V NORMALIZED FAILURE RATE Device Junction Temperature versus Time to 0.1% Bond Failures Junction Temperature C 80 90 100 110 120 130 140 Time, Hours 1,032,200 419,300 178,700 79,600 37,000 17,800 8,900 Time, Years 117.8 47.9 20.4 9.4 4.2 2.0 1.0 FAILURE RATE OF PLASTIC = CERAMIC UNTIL INTERMETALLICS OCCUR TJ = 130 C TJ = 120 C TJ = 110 C TJ = 100 C TJ = 80 C 100 TIME, YEARS TJ = 90 C 1 1 10 1000 Figure 3. Failure Rate vs. Time Junction Temperature http://onsemi.com 2 MC74VHC1G14 DC ELECTRICAL CHARACTERISTICS VCC (V) 3.0 4.5 5.5 3.0 4.5 5.5 3.0 4.5 5.5 VIN VT - Min IOH = -50 mA IOH = -4 mA IOH = -8 mA VOL Maximum Low-Level Output Voltage VIN VT + Max IOL = 50 mA IOL = 4 mA IOL = 8 mA IIN ICC Maximum Input Leakage Current Maximum Quiescent Supply Current VIN = 5.5 V or GND VIN = VCC or GND 2.0 3.0 4.5 3.0 4.5 2.0 3.0 4.5 3.0 4.5 0 to 5.5 5.5 TA = 25C Min 1.85 2.86 3.50 0.9 1.35 1.65 0.30 0.40 0.50 1.9 2.9 4.4 2.58 3.94 0.0 0.0 0.0 0.1 0.1 0.1 0.36 0.36 0.1 1.0 Typ 2.0 3.0 3.6 1.5 2.3 2.9 0.57 0.67 0.74 2.0 3.0 4.5 Max 2.20 3.15 3.85 1.65 2.46 3.05 1.20 1.40 1.60 0.9 1.35 1.65 0.30 0.40 0.50 1.9 2.9 4.4 2.48 3.80 0.1 0.1 0.1 0.44 0.44 1.0 20 1.20 1.40 1.60 TA 85C Min Max 2.20 3.15 3.85 0.9 1.35 1.65 0.30 0.40 0.50 1.9 2.9 4.4 2.34 3.66 0.1 0.1 0.1 0.52 0.52 1.0 40 1.20 1.40 1.60 -55 TA 125C Min Max 2.20 3.15 3.85 Unit V Symbol VT+ Parameter Positive Threshold Voltage Negative Threshold Voltage Hysteresis Voltage Test Conditions VT- V VH V VOH Minimum High-Level Output Voltage V V V V mA mA II I I III I I I I I I IIIIIIIIIIIIIIIIIIIIIIIIIIIIII I I IIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIII I I I II I I I I I IIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIII III I I I II I I II I I I IIIIIIIIIIIIIIIIIIIIIIIIIIIIIII I I I II I I I I I II I I I I IIIII I I II I I I IIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIII I IIIIIIIIIIIIIIIIIIIII I IIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIII I I I II I I I I I II I I I I I IIIIIII I II I I IIIIIIIIIIIIIIIIIIIIIIIIIIIIIII IIIIIIIIIIIIIIIIIIIIIIIIIIIII I I II I I I IIIIIIIIIIIIIIIIIIIIIIIIIIIIIIII I I IIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIII IIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIII IIIIIIIIII I I II IIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIII AC ELECTRICAL CHARACTERISTICS Input tr = tf = 3.0 ns TA = 25C Typ 7.0 8.5 4.0 5.5 5 TA 85C -55 TA 125C Min 1.0 1.0 1.0 1.0 Max Symbol tPLH, tPHL Parameter Test Conditions Min Max Min 1.0 1.0 1.0 1.0 Max Unit ns Maximum Propagation Delay, A to Y VCC = 3.3 0.3 V VCC = 5.0 0.5 V CL = 15 pF CL = 50 pF CL = 15 pF CL = 50 pF 12.8 16.3 15.0 18.5 10.0 12.0 10 17.0 20.5 11.5 13.5 10 8.6 10.6 10 CIN Maximum Input Capacitance pF Typical @ 25C, VCC = 5.0 V 7.0 CPD Power Dissipation Capacitance (Note 6) pF 6. CPD is defined as the value of the internal equivalent capacitance which is calculated from the operating current consumption without load. Average operating current can be obtained by the equation: ICC(OPR) = CPD VCC fin + ICC. CPD is used to determine the no-load dynamic power consumption; PD = CPD VCC2 fin + ICC VCC. http://onsemi.com 3 MC74VHC1G14 A or B 50% GND tPLH Y 50% VCC tPHL VCC Figure 4. Switching Waveforms INPUT CL* OUTPUT *Includes all probe and jig capacitance. A 1-MHz square input wave is recommended for propagation delay tests. Figure 5. Test Circuit ORDERING INFORMATION Device MC74VHC1G14DFT1 MC74VHC1G14DFT1G MC74VHC1G14DFT2 MC74VHC1G14DFT2G MC74VHC1G14DTT1 MC74VHC1G14DTT1G Package SC-88A/SOT-353 SC-88A/SOT-353 (Pb-Free) SC-88A/SOT-353 SC-88A/SOT-353 (Pb-Free) SOT-23/TSOP-5 SOT-23/TSOP-5 (Pb-Free) 3000/Tape & Reel Shipping For information on tape and reel specifications, including part orientation and tape sizes, please refer to our Tape and Reel Packaging Specifications Brochure, BRD8011/D. http://onsemi.com 4 MC74VHC1G14 PACKAGE DIMENSIONS SC-88A, SOT-353, SC-70 CASE 419A-02 ISSUE J A G 5 4 NOTES: 1. DIMENSIONING AND TOLERANCING PER ANSI Y14.5M, 1982. 2. CONTROLLING DIMENSION: INCH. 3. 419A-01 OBSOLETE. NEW STANDARD 419A-02. 4. DIMENSIONS A AND B DO NOT INCLUDE MOLD FLASH, PROTRUSIONS, OR GATE BURRS. S 1 2 3 -B- DIM A B C D G H J K N S D 5 PL 0.2 (0.008) M B M N J C INCHES MIN MAX 0.071 0.087 0.045 0.053 0.031 0.043 0.004 0.012 0.026 BSC --- 0.004 0.004 0.010 0.004 0.012 0.008 REF 0.079 0.087 MILLIMETERS MIN MAX 1.80 2.20 1.15 1.35 0.80 1.10 0.10 0.30 0.65 BSC --- 0.10 0.10 0.25 0.10 0.30 0.20 REF 2.00 2.20 H K SOLDERING FOOTPRINT* 0.50 0.0197 0.65 0.025 0.65 0.025 0.40 0.0157 1.9 0.0748 SCALE 20:1 mm inches *For additional information on our Pb-Free strategy and soldering details, please download the ON Semiconductor Soldering and Mounting Techniques Reference Manual, SOLDERRM/D. http://onsemi.com 5 MC74VHC1G14 PACKAGE DIMENSIONS TSOP-5 CASE 483-02 ISSUE F NOTE 5 2X D 5X 0.20 C A B 5 1 2 4 3 0.10 T 0.20 T L G A B S M K DETAIL Z 2X NOTES: 1. DIMENSIONING AND TOLERANCING PER ASME Y14.5M, 1994. 2. CONTROLLING DIMENSION: MILLIMETERS. 3. MAXIMUM LEAD THICKNESS INCLUDES LEAD FINISH THICKNESS. MINIMUM LEAD THICKNESS IS THE MINIMUM THICKNESS OF BASE MATERIAL. 4. DIMENSIONS A AND B DO NOT INCLUDE MOLD FLASH, PROTRUSIONS, OR GATE BURRS. 5. OPTIONAL CONSTRUCTION: AN ADDITIONAL TRIMMED LEAD IS ALLOWED IN THIS LOCATION. TRIMMED LEAD NOT TO EXTEND MORE THAN 0.2 FROM BODY. DIM A B C D G H J K L M S MILLIMETERS MIN MAX 3.00 BSC 1.50 BSC 0.90 1.10 0.25 0.50 0.95 BSC 0.01 0.10 0.10 0.26 0.20 0.60 1.25 1.55 0_ 10 _ 2.50 3.00 DETAIL Z J C 0.05 H T SEATING PLANE SOLDERING FOOTPRINT* 1.9 0.074 0.95 0.037 2.4 0.094 1.0 0.039 0.7 0.028 SCALE 10:1 mm inches *For additional information on our Pb-Free strategy and soldering details, please download the ON Semiconductor Soldering and Mounting Techniques Reference Manual, SOLDERRM/D. ON Semiconductor and are registered trademarks of Semiconductor Components Industries, LLC (SCILLC). SCILLC reserves the right to make changes without further notice to any products herein. SCILLC makes no warranty, representation or guarantee regarding the suitability of its products for any particular purpose, nor does SCILLC assume any liability arising out of the application or use of any product or circuit, and specifically disclaims any and all liability, including without limitation special, consequential or incidental damages. "Typical" parameters which may be provided in SCILLC data sheets and/or specifications can and do vary in different applications and actual performance may vary over time. All operating parameters, including "Typicals" must be validated for each customer application by customer's technical experts. SCILLC does not convey any license under its patent rights nor the rights of others. SCILLC products are not designed, intended, or authorized for use as components in systems intended for surgical implant into the body, or other applications intended to support or sustain life, or for any other application in which the failure of the SCILLC product could create a situation where personal injury or death may occur. Should Buyer purchase or use SCILLC products for any such unintended or unauthorized application, Buyer shall indemnify and hold SCILLC and its officers, employees, subsidiaries, affiliates, and distributors harmless against all claims, costs, damages, and expenses, and reasonable attorney fees arising out of, directly or indirectly, any claim of personal injury or death associated with such unintended or unauthorized use, even if such claim alleges that SCILLC was negligent regarding the design or manufacture of the part. SCILLC is an Equal Opportunity/Affirmative Action Employer. This literature is subject to all applicable copyright laws and is not for resale in any manner. PUBLICATION ORDERING INFORMATION LITERATURE FULFILLMENT: Literature Distribution Center for ON Semiconductor P.O. Box 5163, Denver, Colorado 80217 USA Phone: 303-675-2175 or 800-344-3860 Toll Free USA/Canada Fax: 303-675-2176 or 800-344-3867 Toll Free USA/Canada Email: orderlit@onsemi.com N. American Technical Support: 800-282-9855 Toll Free USA/Canada Europe, Middle East and Africa Technical Support: Phone: 421 33 790 2910 Japan Customer Focus Center Phone: 81-3-5773-3850 ON Semiconductor Website: www.onsemi.com Order Literature: http://www.onsemi.com/orderlit For additional information, please contact your local Sales Representative http://onsemi.com 6 MC74VHC1G14/D |
Price & Availability of MC74VHC1G1407
 |
|
|
|
|
All Rights Reserved © IC-ON-LINE 2003 - 2022 |
| [Add Bookmark] [Contact Us] [Link exchange] [Privacy policy] |
|
Mirror Sites : [www.datasheet.hk]
[www.maxim4u.com] [www.ic-on-line.cn]
[www.ic-on-line.com] [www.ic-on-line.net]
[www.alldatasheet.com.cn]
[www.gdcy.com]
[www.gdcy.net] |